IEC 62196: plugs, sockets, connectors and inlets
The IEC series for the mechanical and electrical interface between cable and car or charger: which contacts exist, their dimensions and ratings. Part 2 covers the AC Types 1, 2 and 3, part 3 the DC configurations including the CCS combo inlets.
The parts
| Part | Covers |
|---|---|
| IEC 62196-1 | General requirements for all accessories: ratings, marking, protection against electric shock, temperature rise, mechanical strength, tests |
| IEC 62196-2 | Dimensional compatibility of AC accessories with pins and contact tubes: Type 1, Type 2, Type 3 |
| IEC 62196-3 | Dimensional compatibility of DC and combined AC/DC vehicle couplers: the configurations AA, BB, EE and FF |
| IEC TS 62196-3-1 | Additional requirements for DC vehicle couplers with thermal management (liquid cooled cables) |
| IEC 62196-6 | DC couplers for systems where protection relies on electrical separation (light vehicles, with IEC 61851-25) |
The part numbers 3-1 and 6 and their scope are given from memory of the series and should be checked against the current IEC catalogue.
The terms are fixed by the standard: a plug and socket outlet join a cable to the charger, a vehicle connector and vehicle inlet join the cable to the car. Together they form a vehicle coupler. Whether the cable is fixed to the charger or free is the connection case (A, B or C) of IEC 61851-1.
AC types (part 2)
| Type | Also known as | Contacts | Typical rating | Where |
|---|---|---|---|---|
| Type 1 | SAE J1772 coupler | L1, L2/N, PE, CP, PP (5) | Single phase, up to 32 A in IEC terms, up to 80 A under SAE J1772 | North America, Japan, early imports |
| Type 2 | The European plug | L1, L2, L3, N, PE, CP, PP (7) | Three phase up to 63 A, single phase up to 70 A | Europe and many other regions, mandated for public AC in the EU |
| Type 3 | Shuttered socket systems (3A, 3C) | variants with and without CP | Low power | Formerly Italy and France, now replaced by Type 2 |
The maximum currents per type differ between the socket outlet, the vehicle connector and the edition. Verify them in the rating tables of IEC 62196-2 before using them as limits.
Type 1 identifies the connector through a resistor network on PP that also changes when the latch button is pressed, so the car can stop drawing current before the plug is pulled. Type 2 uses a resistor between PP and PE to code the current rating of a detachable cable. The tool reads that coding from a CP log in PP-01.
DC configurations (part 3)
| Configuration | System | Shape | Communication |
|---|---|---|---|
| AA | CHAdeMO (system A) | Separate round DC connector with DC contacts and signal pins | CAN plus analogue lines |
| BB | GB/T (system B) | Separate DC connector with DC contacts, CAN pair, auxiliary supply and detection pins | CAN (GB/T 27930) |
| EE | CCS1, Combo 1 | Type 1 upper part (CP, PP, PE) above two DC contacts | PLC on CP (ISO 15118-3) |
| FF | CCS2, Combo 2 | Type 2 upper part (CP, PP, PE and AC contacts) above two DC contacts | PLC on CP (ISO 15118-3) |
- A combo inlet accepts both the AC plug (upper part only) and the DC connector (upper part plus DC contacts). With a DC connector in a CCS2 inlet the AC contacts stay empty; the connector carries only CP, PP and PE in the upper part.
- The CP and PP contacts of the combo connectors are those of Type 1 or Type 2, which is why the Control Pilot behaviour of IEC 61851-1 and the PLC of ISO 15118-3 are shared between AC and DC.
- Configurations CC and DD appeared in earlier drafts for other combo layouts and are not used in the field.
The status of configurations CC and DD, and the DC voltage and current ratings of each configuration in the current edition (1000 V class, higher currents with cooled cables), are to be verified against IEC 62196-3.
Ratings and temperature
An accessory is rated for a voltage, a current and a temperature rise at that current. High power DC connectors exceed the uncooled current rating and use liquid cooled cables and temperature sensors in the connector; the charger derates when the sensor reports a high temperature. In a capture this appears as EVSEMaximumCurrentLimit falling during the CurrentDemand loop while the car still asks for more, or as the EVSECurrentLimitAchieved flag set.
A slow session where the charger limit drops after a few minutes is often connector or cable temperature derating, not a protocol problem. Compare the charger limit with the car's request over time.
Sources
- IEC 62196-1, general requirements
- IEC 62196-2, AC pin and contact tube accessories, Types 1, 2 and 3
- IEC 62196-3, DC and AC/DC accessories, configurations AA, BB, EE and FF
- IEC 61851-1:2017, Annex B for the proximity resistor coding