ISO 15118-8: wireless communication

The Wi-Fi based link layer for charging without a pilot wire: wireless power transfer (WPT) and automated connection devices such as pantographs (ACD). It replaces ISO 15118-3 below the IP layer; the messages above are those of ISO 15118-20.

Why not powerline

  • Wireless power transfer has no cable at all, so there is no pilot wire to carry powerline signals.
  • An automated connection device (a pantograph on a bus depot mast, or an underbody connector) only makes contact after the vehicle has parked. The car and charger need to talk before that: to find each other, to align the vehicle and to agree that contact may be made.
  • A radio link also allows the communication to start while the vehicle is still approaching, which is needed for guidance and fine positioning over a WPT ground pad.

What the part defines

ISO 15118-8 profiles IEEE 802.11 (Wi-Fi) for this purpose. The charging site runs access points; the vehicle is a station that joins them. The part says which Wi-Fi features and bands are used, how the charging site announces itself and its charging capabilities in the beacons and probe responses, how the vehicle selects the right network, and how IPv6 then runs over it so that SDP and ISO 15118-20 work as on a cable.

LayerConductive (cable)Wireless
PhysicalHomePlug Green PHY on the pilot (ISO 15118-3)IEEE 802.11 (ISO 15118-8)
Finding the peerSLAC: attenuation measurement picks the charger at the end of the cableDiscovery of the charging site network, then pairing and positioning of the vehicle to one pad or pantograph
Network and transportIPv6, SDP, TCP and TLSthe same
ApplicationDIN SPEC 70121, ISO 15118-2, ISO 15118-20ISO 15118-20 (WPT, ACDP services)

Which 802.11 amendments and bands the first and second editions require, and the exact information elements used for the charging site announcement, are to be verified against the part.

Association and pairing

A radio network covers a whole parking area, so joining it does not say which pad or mast the vehicle is at, the same problem SLAC solves on a cable. For WPT, ISO 15118-20 adds fine positioning and pairing steps in its WPT message set so the vehicle and the ground assembly under it confirm they belong together. For pantograph charging (ACDP) the vehicle and the connection device agree on the stop position and the connection before energy flows. Only after pairing does the energy transfer start.

  1. EVSE: Wi-Fi beacon, the charging site announces its network and capabilities
  2. EV: Association, the vehicle joins the site network
  3. EV: SDP request, as on a cable: find the SECC address and port
  4. EV: supportedAppProtocolReq, ISO 15118-20 over TLS 1.3
  5. both: Positioning and pairing, WPT or ACDP specific messages of ISO 15118-20
  6. EV: PowerDeliveryReq, energy transfer starts

The flow is a simplified picture of the order of steps. The detailed pairing messages are in the WPT and ACDP clauses of ISO 15118-20 and its companion documents.

In this tool

The tool reads captures with Ethernet framing, not raw 802.11 or radiotap frames. A capture of the IPv6 traffic taken on the wired side of the access point, or on the station's own interface where frames appear as Ethernet, can be read: SDP, TCP, TLS and the ISO 15118-20 messages are the same as on a cable. A monitor mode capture has to be decrypted and exported as Ethernet first. There is no SLAC and no Control Pilot, so those layers stay empty. The WPT and ACDP message sets are decoded by the ISO 15118-20 module.

Sources

  • ISO 15118-8, wireless physical and data link layer
  • ISO 15118-20:2022, WPT and ACDP services that run over it
  • IEEE 802.11, the Wi-Fi standard it profiles