SAE J3400: the NACS coupler
Tesla's charging connector, opened as the North American Charging System and standardised by SAE as J3400. One compact inlet carries AC and DC on the same two power contacts; the pilot, powerline and protocols are the same as for CCS.
The coupler
| Contact | Function |
|---|---|
| Power 1 | AC L1, or DC+ during DC charging |
| Power 2 | AC L2/N, or DC- during DC charging |
| PE | Protective earth |
| CP | Control Pilot, same signal as J1772, carries powerline for DC and for ISO 15118 on AC |
| PP | Proximity detection |
- Five contacts in total. The same two power contacts carry AC or DC, so one inlet and one connector serve both, unlike the CCS1 combo inlet with its separate DC contacts.
- The charger decides what it puts on the power contacts. The car must know which it is getting: the pilot duty cycle (nominal for AC, 5 percent for high level communication) and the protocol exchange tell it whether to route the contacts to the on-board charger or to the battery.
- The coupler is rated for AC and DC with a voltage class suited for 400 V and 800 V batteries; exact ratings are in the standard.
The voltage and current ratings for AC and DC, and the proximity circuit details, are to be verified against J3400.
Communication is CCS communication
J3400 does not add a new protocol. The Control Pilot follows J1772 and IEC 61851-1, DC charging uses HomePlug Green PHY on the pilot with SLAC (ISO 15118-3), and the application layer is DIN SPEC 70121, ISO 15118-2 or ISO 15118-20. A capture from a J3400 session is analysed by the same modules and checks as a CCS1 capture: CP, SL, SD, TC, TL, HS, SQ and TIM.
Tesla vehicles and Superchargers built before the opening of the standard also used a proprietary protocol. That protocol is undocumented and not read by this tool; recent Tesla products also speak the standard protocols.
Adapters
- Because the signalling is identical, a CCS1 to J3400 adapter (for a CCS1 car at a J3400 charger, or the reverse) only has to route the contacts: pilot to pilot, proximity to proximity, power to power. It does not translate messages.
- An adapter adds contact resistance and its own temperature limit, and a car or charger may limit current when it knows an adapter is in use. A session that runs at reduced power with an adapter is not by itself a protocol fault.
- AC adapters between J1772 and J3400 work the same way for the pilot; the power contacts map to L1 and L2/N.
- SAE describes the requirements for adapters in a companion document to J3400.
The adapter document number (J3400/1 in most references) and its requirements are to be verified.
When a J3400 session fails with an adapter, capture on the charger side of the adapter if possible. A poor pilot contact in the adapter appears as powerline errors (SLAC retries, TCP retransmissions) before it appears as a pilot level fault.
Timeline
| When | What |
|---|---|
| November 2022 | Tesla publishes the connector design and names it the North American Charging System |
| 2023 | Most car makers selling in North America announce a move to the connector; SAE starts standardisation |
| Late 2023 | SAE publishes J3400 as a Technical Information Report |
| 2024 onwards | Adapter based access for CCS1 cars to Supercharger networks; recommended practice work on J3400 continues |
| From model year 2025 | New vehicles with a J3400 inlet begin to appear |
The dates are approximate and the publication status of J3400 (TIR versus Recommended Practice, and the dates of later revisions) is to be verified.
Sources
- SAE J3400, North American Charging System (NACS) electric vehicle coupler
- SAE J1772, Control Pilot behaviour it relies on
- ISO 15118-3, DIN SPEC 70121, ISO 15118-2 and -20, communication used over it