Worked example: the BMS stops a GB/T session with BST

The gbt-bst demo read step by step: a GB/T 27930 session that charges at 150 A until the BMS sends BST reporting the charging connector over temperature at 20.0 s, then CST, the current falling to zero, and the statistics BSD and CSD.

What you see

  • Load the demo BMS stops with BST (gbt-bst): a candump log of 21 s, 657 CAN frames between the charger at address 0x56 and the BMS at 0xF4.
  • Stage strip: Handshake, Recognition, Parameters, Ready, Energy transfer and Stop all passed.
  • No findings. GB-01 to GB-08, CAN-01 and CAN-02 pass: every step was answered in time, the output stayed at or below the demand, and GB-07 finds BST followed by BSD.

The verdict

Stopped early, Vehicle fault, likely party EV, confidence high. The explanation reads: the BMS stopped at 20.0 s reporting connector over temperature. The chain of evidence is empty, because no check failed: the session ended in the order the standard describes, for a reason the BMS gave.

Reading the capture step by step

  1. EVSE: CHM, 0.000 s, repeated every 250 ms
  2. EV: BHM, 1.020 s: maximum allowable voltage 420 V
  3. EV: BRM, 3.060 s, by broadcast transport: lithium iron phosphate, 120 Ah, 355 V
  4. EV: BCP, 3.600 s: up to 200 A and 420 V
  5. EVSE: CML, 4.000 s: up to 250 A and 500 V
  6. EV: BRO, 4.500 s: ready
  7. EVSE: CRO, 4.800 s: ready
  8. both: BCL, BCS, CCS, BSM, 5.0 to 20.0 s: demand every 50 ms, status every 250 ms (BCS, nine bytes, by broadcast transport); 150 A from 10 s on
  9. EV: BST, 20.000 s: no stop reason, fault connector over temperature
  10. EVSE: CCS, 20.010 s: still 150 A, charging not allowed
  11. EVSE: CST, 20.200 s: BMS stopped actively
  12. EVSE: CCS, 20.260 s: 75 A; 20.510 s: 0 A
  13. EV: BSD, 20.800 s: final state of charge 32 %
  14. EVSE: CSD, 21.000 s: 0 min, 0.2 kWh
  • The start is clean: each step of the startup sequence is answered within the time of the profile, and the charger output follows the BMS demand (GB-05).
  • Up to 20 s the BSM of the car reports its highest battery temperature at 28 C and charging permitted. The battery is not the problem.
  • The BST at 20.000 s carries no normal end reason in its first byte, such as a state of charge or voltage target, and reads 01 in the two bit field for the connector over temperature in its second byte. The next BSM reports charging not permitted.
  • The charger does what it should: it answers with CST 200 ms later, giving as its reason that the BMS stopped first, takes the current to zero within about 0.5 s, and both sides exchange their statistics.

The BST, CST and BSM field tables of this tool, with their two bit fields (00 normal, 01 true, 10 not credible), are marked for verification against GB/T 27930-2015, which is not freely available. Check the bit positions against the document before quoting them.

What the cause is

  • The BMS measures the temperature at the charging connector on the vehicle side and stopped the charge when it rose too high. The heat is at the contact between the charger plug and the vehicle inlet, where 150 A flows.
  • The verdict names the car because the car stopped. The heat can come from either half of the connection: worn or dirty pins in the charger plug, a damaged vehicle inlet, a plug that is not fully inserted, or a faulty temperature sensor in the inlet.
  • The capture holds the decision of the BMS, not the temperature it measured, so it cannot tell a real hot spot from a bad sensor.

What to fix

  • Inspect the pins of the charger plug and of the vehicle inlet for discoloration, pitting or dirt, and check that the plug locks fully home.
  • Swap one half at a time: this car at another charger, another car at this charger. A connector over temperature that follows the charger cable points at its plug.
  • Read the inlet temperature from the vehicle diagnostics during a repeat charge, and compare it with a thermal camera on the connector.
  • A CHAdeMO or GB/T session stops lists the stop reasons and error messages of GB/T and CHAdeMO side by side.

How to confirm the fix

  • A repeat charge at 150 A runs past 20 s without a BST.
  • When the BMS does stop, BST carries a normal end reason such as the state of charge target, and the verdict reads Completed normally, like the gbt demo.

Sources

  • GB/T 27930-2015, BST, CST, BSD and CSD, the end of charging
  • IEC 61851-24, digital communication for DC charging, the GB/T annex
  • SPEC.md of this tool, FR-ENC-05, the failing demo sessions