Highway and urban fast charging hubs
High power DC charging along motorways and in city hubs: power cabinets shared by several dispensers, the AFIR targets in the EU and the NEVI minimum standards in the US, uptime expectations, and what to record when a fast charge fails to start or stops.
The setting
Drivers on a long trip or without a home charger stop for a short break and expect the car to charge at the fastest rate it can take. The sites range from a pair of chargers at a service area to hubs with many points. Involved are the charge point operator, the site host, the network operator, the drivers and their mobility service providers, and the public funders whose rules set many of the requirements.
- Chargers are DC; the funding rules below ask for at least 150 kW per point. The car decides how much it takes, following its charging curve (Why a charging curve looks the way it does).
- Many sites use a power cabinet that feeds several dispensers and moves power modules between them: the second car to plug in may get less than the sticker on the dispenser. The Inside a charger page explains the split.
- The connector depends on the region: CCS1, CCS2, SAE J3400, CHAdeMO or GB/T (Connectors compared).
Rules for public fast charging
| Region | Rule | Requirement as published |
|---|---|---|
| European Union (Europe: AFIR, Type 2, CCS2 and ISO 15118) | AFIR, Regulation (EU) 2023/1804 | Along the TEN-T core network, a recharging pool at least every 60 km. By 31 December 2025 each pool offers at least 400 kW with at least one point of 150 kW or more; by 31 December 2027 at least 600 kW with at least two points of 150 kW or more (as summarised by the ICCT). AFIR applies from 13 April 2024. |
| United States (North America: J1772, CCS1, J3400 and the NEVI standards) | NEVI minimum standards, 23 CFR 680 (final rule February 2023) | On designated corridors: at least four CCS ports per site, each able to deliver 150 kW at the same time, output between 250 and 920 V DC, stations every 50 miles and within one mile of the interstate, and an average annual uptime of at least 97 percent per port (with exclusions). |
| United States, communication | 23 CFR 680.108 | Chargers conform to ISO 15118-3, have hardware able to run ISO 15118-2 and ISO 15118-20, and by 28 February 2024 run ISO 15118-2 software able to do Plug and Charge; OCPP 2.0.1 to the network and OCPI 2.2.1 between networks by the same date. |
The NEVI program itself changed in 2025: the Federal Highway Administration froze state plans on 6 February 2025 and on 11 August 2025 published interim final guidance that replaced all earlier guidance, gave states more freedom (for example on the distance between stations) and reopened the remaining funding. The guidance leaves the minimum standards of 23 CFR 680 in place (Federal Register, August 2025).
The UK Public Charge Point Regulations 2023 (reliability, contactless payment, helpline and open data duties) and the rules of other regions are not checked for this page. See United Kingdom: smart charge points, the Public Charge Point Regulations and Type 2 with CCS2, North America: J1772, CCS1, J3400 and the NEVI standards and the other region pages.
Communication and backend
- Car and charger speak DIN SPEC 70121 or ISO 15118-2 over powerline, and more and more ISO 15118-20; Plug and Charge adds TLS and certificates (Plug and Charge and its PKI).
- Every charger reports to its operator with OCPP; a hub may add a local controller that shares power between dispensers and the site limit.
- Payment and roaming run between backends (Payment, roaming and Plug and Charge): the driver sees an app, a card, a terminal or nothing at all with Plug and Charge.
What fails
A fast charge has more steps than an AC session, and each one can end it before any energy flows. In a capture, a failed DC session ends at one of these places:
- SLAC that does not match, often with high attenuation on a long or damaged cable (Car plugged in, no SLAC match).
- TLS that fails for Plug and Charge: an unknown or expired certificate (The TLS handshake fails).
- Cable check: the insulation test fails or the charger never finishes it (Stage: DC cable check and isolation test).
- Pre-charge: the charger output does not reach the voltage of the car in time (Stage: DC pre-charge).
- A stop during charging from either side: a charger fault, a thermal limit on the cable or a car that ends the session (The session stops during charging).
- Lower power than expected: a shared cabinet, a hot battery or a derated cable (Charging is slower than expected).
Field statistics on how often public fast charging fails are collected on Reliability of public charging: what field data says.
What to record and test
- The powerline capture from the first Control Pilot change to the unplug, with the TLS key log if the charger uses TLS, and the OCPP log of the charger for the same minutes.
- For every failed start, the car model and software version and the charger model and firmware: most start failures are one pair that does not work together.
- Tests: a start on every dispenser of a shared cabinet with two cars at once, a charge at low and at high state of charge, Plug and Charge and card starts, an emergency stop, and a charger reboot during a session. DC test cases, worked has the forms.
In this tool
- Demos: iso20 is a clean ISO 15118-20 DC session; precharge-fail stalls at 312 V of 400 V; cablecheck-fail is a DIN SPEC 70121 cable check answered with FAILED and EVSE_Shutdown; chademo is a CHAdeMO session read from CAN frames.
- DC-01 judges pre-charge; TIM-02 times the Ongoing loops, including the cable check; the SL checks judge SLAC and the TL checks the TLS handshake.
- The Timers tool sorts every timed interval by the share of its limit used, so a cable check at 90 percent of its timeout shows before it fails. The Curve tool shows whether the charger delivered what the car asked for.
- Batch mode shows, over a day of captures from a hub, how sessions ended per charger and per car.
Sources
- Regulation (EU) 2023/1804 on the deployment of alternative fuels infrastructure (AFIR), Articles 3 and 4: targets for light and heavy duty vehicles on the TEN-T network; Article 5: ad hoc payment
- ICCT: Alternative Fuels Infrastructure Regulation, EU policy update, April 2023; power per pool and per point on the TEN-T core network for 2025 and 2027
- FHWA: National Electric Vehicle Infrastructure Standards and Requirements, final rule, 23 CFR 680, Federal Register 88 FR, 28 February 2023; effective 30 March 2023
- ZETA: The Final Rules: National Electric Vehicle Infrastructure Formula Program Summary, four ports, 150 kW each, 250 to 920 V DC, 97 percent uptime, spacing
- 23 CFR 680.108: interoperability of EV charging infrastructure, ISO 15118-3, ISO 15118-2 and -20 hardware, Plug and Charge, OCPP 2.0.1, OCPI 2.2.1 by 28 February 2024
- American Public Power Association: FHWA publishes interim final guidance for the NEVI program, 11 August 2025; replaces the earlier guidance; plans frozen since 6 February 2025
- Federal Register: NEVI Formula Program interim final guidance, August 2025; the minimum standards of 23 CFR 680 stay in force
- Crowell (Climate Solutions Law): new FHWA guidance on EV infrastructure, September 2025; minimum standards and requirements of 23 CFR 680 retained
- IEC 61851-23, DC charging station requirements